Featured Project

Modeling of Spalling in PFC3D — A Quantitative Assessment

PROJECT DESCRIPTION

The Swedish Nuclear Waste Management Company (SKB) is interested in developing a 3D discrete model to predict spalling on the excavation boundaries of underground repositories for the long-term storage of spent nuclear fuel. Previous work showed that spalling could be captured using a flat-joint contact model material in PFC3D (Potyondy and Mas Ivars, 2020). This project provided a quantitative assessment of modeling spalling using PFC3D to study both lab- and tunnel-scale behavior.

ITASCA'S ROLE

Itasca evaluated the ability of the PFC3D code to model spalling by simulating the Atomic Energy of Canada Limited Underground Research Laboratory (URL) Mine-by Experiment test tunnel in the Lac du Bonnet granite batholith at a depth of 443 m. The spalling process observed in this tunnel resulted in well-developed v-shaped notches in the roof and floor, as seen in Figure 1. The notch tip consisted of a process zone in which the rock had been crushed. The notch sides consisted of thin slabs that spalled off the excavation boundary where some of the slabs were as thick as the grain size of the rock.

Using the flat-joint contact model, three PFC3D materials were studied using different unbreakable grain shapes, as seen in Figure 2: spherical, Voronoi, and tetrahedral. The three flat-jointed materials were calibrated to match the lab-scale response of intact Lac du Bonnet granite during direct-tension and triaxial compression tests.

The Mine-by Experiment simulations were performed using FLAC3D-PFC3D coupled models, in which a slice of the PFC3D material (approximately four grains thick) was embedded within a larger FLAC3D model. This improved modeling efficiency by ensuring that the spalling process was captured in the PFC3D region using the fewest number of particles or rigid blocks while maintaining proper far-field boundary conditions as provided by the FLAC3D model.

Figure 1. The completed Mine-by test tunnel showing the well-developed notches in the roof and floor (from Fig. 35 of Martin, 1997).

PROJECT RESULTS

The primary conclusion of this study is that the tetrahedral-grain rock mass material is better suited to model spalling than either of the other two materials for the following reasons: 1) damage lobes[1] are largely absent; and 2) the sharp shape and extent of the notch, as well as the mechanisms occurring in the notch, closely resemble what occurred in the Mine-by Experiment test tunnel. These features are not well matched by either of the other two materials.

Figure 2. PFC3D models of the tunnel using flat-jointed material with different grain shapes (spherical, Voronoi, and tetrahedral). Top is model microstructure, and bottom is excavation-induced damage in the form of broken bonds (blue-shear, red-tensile).

From evaluating the lab-scale behavior, it was established that all PFC3D materials can be calibrated to match most of the material properties of intact Lac du Bonnet granite. As the spalling process occurs at the grain-scale, only a discrete model with a particle size equal to the grain size of the rock will be able to capture the process in detail. Although this is not achievable with current computing power, the discrete model can predict the shape and extent of the notch in the Mine-by Experiment when using a relatively small grain size that is made possible by using a coupled FLAC3D-PFC3D approach.

[1] The damage lobes consist of a crack swarm emanating from the tunnel surface and oriented approximately 45 degrees from the direction of the maximum principal stress, and the cracks are aligned with the compressive force chains. The damage lobes appear to be formed where the stress exceeds the crack-initiation stress of the material. It is unlikely that damage lobes are present in the rock mass surrounding the Mine-by Experiment test tunnel.

REFERENCES

Martin, C.D. (1997) “Seventeenth Canadian Geotechnical Colloquium: The Effect of Cohesion Loss and Stress Path on Brittle Rock Strength,” Canadian Geotechnical Journal, 34, 698–725.

Potyondy, D., and Mas Ivars, D. (2020) “Simulating spalling with a flat-jointed material,” Applied Numerical Modeling in Geomechanics 2020 (Proceedings, 5th International Itasca Symposium, February 2020), paper 03-01. Minneapolis, Minnesota: Itasca.

Potyondy, D., J. Vatcher, and S. Emam (2020) “Modeling of Spalling with PFC3D: A Quantitative Assessment,” Itasca Consulting Group, Inc., Report to Svensk Kärnbränslehantering AB (SKB), Stockholm, Sweden, Ref. 2-5732-02:20R50, October 22, 2020. Minneapolis, Minnesota.

Oficina

U.S. Minneapolis
Itasca Consulting Group, Inc.

Industrias

Energy
Nuclear Waste

Nombre del Cliente

Swedish Nuclear Fuel and Waste Management Company (SKB)

Ubicación

Stockholm, Sweden

Software

PFC